No. | parte # | Fabricante | Descripción | Hoja de Datos |
---|---|---|---|---|
|
|
NXP |
Signal Souces Switch |
|
|
|
NXP |
2 x 7 W stereo Bridge Tied Load BTL audio amplifier s s s s s s s s s Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Pr |
|
|
|
NXP |
CONTROL CIRCUIT FOR SMPS Be sure to visit ChipDocs site for more information http://www.chipdocs.com Be sure to visit ChipDocs site for more information http://www.chipdocs.com |
|
|
|
NXP |
Multiple voltage regulator s Three enable pin controlled standby regulators: x REG1: 5 V / 600 mA controlled by the EN1 input x REG2: 3.3 V / 200 mA controlled by the EN2/3 input x REG3: 1.9 V / 150 mA controlled by the EN2/3 input s Four mode pin controlled switched regulator |
|
|
|
NXP |
Gating / Frequency Divider |
|
|
|
NXP |
26 W BTL and 2 x 13 W SE power amplifiers • Requires very few external components • High output power • Low output offset voltage (BTL channel) • Fixed gain • Diagnostic facility (distortion, short-circuit and temperature detection) • Good ripple rejection • Mode select switch (operating, mu |
|
|
|
NXP |
BTSC-stereo/SAP/DBX decoder and DBX expander • DBX decoder, MPX decoder and SAP decoder on chip • Extensive switching possibilities for the AF outputs and the extra headphone output • Stereo and SAP signal available simultaneously • Reliable stereo/SAP identification by means of the noise detec |
|
|
|
NXP |
4 x 40 W BTL quad car radio power amplifier • Requires very few external components • High output power • Low output offset voltage • Fixed gain • Diagnostic facility (distortion, short-circuit and temperature pre-warning) • Good ripple rejection • Mode select switch (operating, mute and stand |
|
|
|
NXP |
DVB-T channel receiver • 2 and 8 kbytes Coded Orthogonal Frequency Division Multiplexer (COFDM) demodulator (fully DVB-T compliant: ETSI 300-744) • All modes supported, including hierarchical modes • Fully automatic transmission parameters detection (including Fast Fourier |
|
|
|
NXP |
2 to 6 W audio power amplifier are: • single in-line (SIL) construction for easy mounting • separated preamplifier and power amplifier • high output power • thermal protection • high input impedance • low current drain • limited noise behaviour at radio frequencies QUICK REFERENCE |
|
|
|
NXP |
Triple video output amplifier • Typical bandwidth of 5.5 MHz for an output signal of 60 V (p-p) • High slew rate of 900 V/µs • No external components required • Very simple application • Single supply voltage of 200 V • Internal reference voltage of 2.5 V • Fixed gain of 50 • Bla |
|
|
|
NXP |
Universal HiFi audio processor for TV • Multi-source selector switches six AF inputs (three stereo sources or six mono sources) • Each of the input signals can be switched to each of the outputs (crossbar switch) • Outputs for loudspeaker channel, headphone channel and peri-TV connector |
|
|
|
NXP |
Spatial/ stereo and pseudo-stereo sound circuit • Three switched functions: – spatial (widened stereo image) – stereo – pseudo-stereo (artificial stereo from a mono source) • Offset compensated operational amplifiers to reduce switch noise • LED driver outputs to facilitate indication of selected |
|
|
|
NXP |
Signal-sources switch lastic (SOT38); SOT38-1; 1996 July 18. January 1980 2 Philips Semiconductors Signal-sources switch Product specification TDA1029 January 1980 Fig.1 Block diagram. 3 Philips Semiconductors Signal-sources switch RATINGS Limiting values in accord |
|
|
|
NXP |
Class AB stereo headphone driver and benefits Wide temperature range No switch ON/OFF clicks Excellent power supply ripple rejection Low power consumption Short-circuit resistant High performance High signal-to-noise ratio High slew rate Low distortion Large outp |
|
|
|
NXP |
Stereo Continuous Calibration DAC CC-DAC • Voltage output • Space saving packages SO8 or DIP8 • Low power consumption • Wide dynamic range (16-bit resolution) • Continuous Calibration (CC) concept • Easy application: – single 4 to 5.5 V rail supply – output current and bias current are prop |
|
|
|
NXP |
2 x 22 W BTL stereo car radio power amplifier • Requires very few external components • High output power • Low offset voltage at outputs • Fixed gain • Good ripple rejection • Mute/stand-by switch • Load dump protection • AC and DC short-circuit-safe to ground and VP QUICK REFERENCE DATA PARAME |
|
|
|
NXP |
5 W mono BTL audio amplifier DC volume control Few external components Mute mode Thermal protection Short-circuit proof No switch-on and switch-off clicks Good overall stability Low power consumption Low HF radiation ESD protected on all pins. GENERAL DESCRI |
|
|
|
NXP |
TDA8510J • Requires very few external components • High output power • Low output offset voltage (BTL channel) • Fixed gain • Diagnostic facility (distortion, short-circuit and temperature detection) • Good ripple rejection • Mode select switch (operating, mu |
|
|
|
NXP |
12-bit high-speed Analog-to-Digital Converter ADC • 12-bit resolution • Sampling rate up to 55 MHz • −3 dB bandwidth of 190 MHz • 5 V power supplies • Binary or twos-complement CMOS outputs • In-range CMOS-compatible output • TLL-CMOS compatible static digital inputs • 3 to 5 V CMOS-compatible digit |
|