No. | parte # | Fabricante | Descripción | Hoja de Datos |
---|---|---|---|---|
|
|
3PEAK |
High Speed Quad Differential RS422 Receiver Meets the TIA/EIA- 422-B requirements High speed, up to 50Mbps data rate, and tPLH = tPHL = 17 ns typical Low pulse distortion, tsk(p) = 0.7 ns typical -7V ~ +12V Common-Mode Range With ±200mV sensitivity Input Hysteresis: 40 mV typical W |
|
|
|
3PEAK |
Isolated CAN Transceiver • Meet ISO11898 Standard • Support CAN FD and Data Rates up to 5 Mbps • Typical Loop Delay: 110 ns • 5-V Power Supply, 2.25-V to 5.5-V IO Interface • Receiver Common-Mode Input Voltage: ±30 V • Bus Fault Protection: ±42 V • Up to 5-kV RMS Isolation R |
|
|
|
3PEAK |
3.3V~5.0V Full Duplex RS-485 Transceivers 3.3V~5.0V Full Duplex RS-485 Transceivers with polarity control Description ⚫ Exceeds Requirements of EIA-485 Standard ⚫ Hot Plug Circuitry - Tx and Rx Outputs Remain Three- State During Power-up/Power-down ⚫ Supply voltage: 3.0V ~ 5.5V ⚫ Data Rate |
|
|
|
3PEAK |
8-channel I2C Switch Bidirectional Translator of 1:8 I2C Switch Active-Low Reset Input Three address terminals, allowing up to 8 devices on the I2C Bus Operating Power-Supply Voltage Range of 2.3 V to 5.5 V Allows Voltage-Level Translation Between 2.5 V, 3.3 V, |
|
|
|
3PEAK |
Low-Power Fault Protected High-Speed CAN FD Transceiver • Meet the ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5 Physical Layer Standards • Supports CAN FD and Data Rating up to 5 Mbps • Short Propagation Delay Times and Fast Loop Times • 5-V Power Supply, I/O Voltage Range Supports 2.8-V to 5.5-V MCU I |
|
|
|
3PEAK |
Automotive Fault Protected High-Speed CAN FD Transceiver • Meets the ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5 Physical Layer Standards • Supports CAN FD and Data Rating up to 5 Mbps • Short Propagation Delay Times and Fast Loop Times • 5-V Power Supply, I/O Voltage Range Supports 2.8-V to 5.5-V MCU |
|
|
|
3PEAK |
Dual Bidirectional I2C Bus and SMBus Voltage-Level Translator ⚫ Dual bidirectional Translator for SDA and SCL Lines in I2C Applications and SMBus Compatible ⚫ Support multi-mode: Standard-mode (SM), Fastmode (FM), and Fast-mode Plus (FM+) ⚫ Less than 1.5 ns (max) Delay to Accommodate SM and FM I2C devices and m |
|
|
|
3PEAK |
4-channel I2C Switch Bidirectional Translator of 1:4 I2C Switch Active-Low Reset Input Two Address Terminals, Allowing up to Four Devices on the I2C Bus Operating Power-Supply Voltage Range of 2.3 to 5.5V Allow Voltage-Level Translation among 2.5V, 3.3V, and 5V |
|
|
|
3PEAK |
Fault Protected High-Speed CAN FD Transceiver • Meets the ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5 Physical Layer Standards • Supports CAN FD and Data Rating up to 5 Mbps • Short Propagation Delay Times and Fast Loop Times • 5-V Power Supply, I/O Voltage Range Supports 2.8-V to 5.5-V MCU |
|
|
|
3PEAK |
3.3-V Fault Protected High-Speed CAN FD Transceiver • 3.3-V Power Supply, I/O Voltage Range Supports 2.8-V to 5.5-V MCU Interface • Compatible with ISO 11898-2:2016 Physical Layer Standards • Supports CAN FD and Data Rating up to 5 Mbps • Short Propagation Delay Times and Fast Loop Times • Common-Mode |
|
|
|
3PEAK |
3.0V to 5.5V RS-485 Transceivers ⚫ Exceeds Requirements of EIA-485 Standard ⚫ Data Rate: 20Mbps or 500Kbps ⚫ Up to 256 Nodes on a Bus (1/8 unit load) ⚫ Full Fail-safe Receiver (Open, Short, Terminated) ⚫ Wide Supply Voltage 3V to 5.5V ⚫ 1.65V to Vcc Supply for Digital IOs ⚫ Bus-Pin |
|
|
|
3PEAK |
RS-485 Transceivers ◼ High Data Rates: 10Mbps At 5V Supply ◼ 30/50ns (Max) Tx/Rx Propagation Delays; 6ns (Max) Skew ◼ Full Fail-safe (Open, Short, Terminated) Receivers ◼ Up to 256 Nodes on a Bus (1/8 unit load) ◼ Wide Supply Voltage 3V to 5.5V ◼ Low Quiescent Supply Cu |
|
|
|
3PEAK |
3.3-V Fault Protected High-Speed CAN FD Transceiver • 3.3-V Power Supply, I/O Voltage Range Supports 2.8-V to 5.5-V MCU Interface • Compatible with ISO 11898-2:2016 Physical Layer Standards • Supports CAN FD and Data Rating up to 5 Mbps • Short Propagation Delay Times and Fast Loop Times • Common-Mode |
|
|
|
3PEAK |
Enhanced High Performance Bidirectional I2C Isolator Description • Bidirectional I2C Compatible Isolator • Up to1-MHz Operation • 3.75-kV RMS Isolation Rating • ±200-kV/μs typ Static CMTI, ±150 kV/μs typ Dynamic CMTI • Open-drain Outputs with 3.5-mA Side A and 35-mA Side B Sink Current Capability • U |
|
|
|
3PEAK |
Bus-Polarity Correcting RS-485 Transceiver TPT485N ± 18K ESD Protection, Bus-Polarity Correcting RS-485 Transceiver Description ◼ Exceeds Requirements of EIA-485 Standard ◼ Bus-Polarity Correction within 100 ms meet SGCC spec ◼ Data Rate: 300 bps to 500 kbps ◼ Works with Two Configurations: |
|
|
|
3PEAK |
Enhanced High Performance Bidirectional I2C Isolator Description • Bidirectional I2C Compatible Isolator • Up to1-MHz Operation • 3.75-kV RMS Isolation Rating • ±200-kV/μs typ Static CMTI, ±150 kV/μs typ Dynamic CMTI • Open-drain Outputs with 3.5-mA Side A and 35-mA Side B Sink Current Capability • U |
|
|
|
3PEAK |
RS-485 Transceiver ◼ Exceeds Requirements of EIA-485 Standard ◼ Data Rate: 500 kbps ◼ Support Failsafe function ◼ Low Power Consumption: < 1 µA Standby Supply Current ◼ Large Receiver Hysteresis: 60mV ◼ Up to 256 Nodes on a Bus (1/8 unit load) ◼ Wide Supply Voltage 4.5 |
|
|
|
3PEAK |
Automotive Fault Protected High-Speed CAN FD Transceiver • Meets the ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5 Physical Layer Standards • Supports CAN FD and Data Rating up to 5 Mbps • Short Propagation Delay Times and Fast Loop Times • 5-V Power Supply, I/O Voltage Range Supports 2.8-V to 5.5-V MCU |
|
|
|
3PEAK |
Automotive Fault Protected High-Speed CAN FD Transceiver • Meet the ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5 Physical Layer Standards • Supports CAN FD and Data Rating up to 5 Mbps • Short Propagation Delay Times and Fast Loop Times • 5-V Power Supply, I/O Voltage Range Supports 2.8-V to 5.5-V MCU I |
|
|
|
3PEAK |
3.0V to 5.5V RS-485 Transceivers ⚫ Exceeds Requirements of EIA-485 Standard ⚫ Hot Plug Circuitry - Tx and Rx Outputs Remain Three- State During Power-up/Power-down ⚫ Data Rate: 500 Kbps ⚫ Up to 256 Nodes on a Bus (1/8 unit load) at 500kbps ⚫ Full Fail-safe Receiver (Open, Short, Ter |
|