No. | parte # | Fabricante | Descripción | Hoja de Datos |
---|---|---|---|---|
|
|
Texas Instruments |
SINGLE-CHIP RF TRANSMITTER NC description The TRF4900 single-chip solution is an integrated circuit intended for use as a low cost FSK transmitter to establish a frequency-agile RF link. The device is available in a 24-lead TSSOP package and is designed to provide a fully-fun |
|
|
|
Texas Instruments |
SINGLE-CHIP MULTIBAND RF TRANSMITTER a fully-integrated VCO. Only the PLL loop filter is external to the device. Two fully-programmable operation modes, Mode0 and Mode1, allow extremely fast switching between two preprogrammed settings (for example, TX_frequency_0/TX_frequency_1; …) wit |
|
|
|
Texas Instruments |
SYNTHESIZER provide maximum flexibility for the design of 900-MHz wireless systems. The main synthesizer consists of a 32/33-modulus prescaler with an 11-bit counter, a phase-frequency detector, and a charge pump. The phase-frequency detector is referenced to a |
|
|
|
Texas Instruments |
NFC Transceiver 1 • Supports Near Field Communication (NFC) Standards NFCIP-1 (ISO/IEC 18092) and NFCIP‑2 (ISO/IEC 21481) • Completely Integrated Protocol Handling for ISO/IEC 15693, ISO/IEC 18000-3, ISO/IEC 14443 A and B, and FeliCa™ • Integrated Encoders, Decoders |
|
|
|
Texas Instruments |
Multiprotocol Fully Integrated 13.56-MHz RFID Reader/Writer IC 1 • Completely Integrated Protocol Handling for ISO/IEC 15693, ISO/IEC 18000-3, ISO/IEC 14443A, ISO/IEC 14443B, NFC Forum Device Types 2 to 5, and FeliCa™ • Input Voltage Range: 2.7 VDC to 5.5 VDC • Programmable Output Power: +20 dBm (100 mW) or +23 |
|
|
|
Texas Instruments |
SILICON MOSFET POWER AMPLIFIER ilored specifically for global systems for mobile communications (GSM). It uses Texas Instruments RFMOS™ process and consists of a three-stage amplifier with output power control. Few external components are required for operation. The TRF7610 amplif |
|
|
|
Texas Instruments |
QUADRATURE MODULATORS 1 •2 75-dBc Single-Carrier WCDMA ACPR at –11-dBm Channel Power • Low Noise Floor: –163 dBm/Hz • OIP3 of 23 dBm • P1dB of 9 dBm • Unadjusted Carrier Feedthrough of –40 dBm • Unadjusted Side-Band Suppression of –40 dBc • Single Supply: 4.5 V –5.5 V Oper |
|
|
|
Texas Instruments |
Quadrature Modulator •1 IQ Modulator with Integrated PLL and VCO • Integer-N/Fractional-N PLL • Modulator Supports 400 MHz to 4200 MHz • PLL and VCO Supports 280 MHz to 4100 MHz • OIP3 at 900 MHz = 31 dBm • OIP3 at 1800 MHz = 30 dBm • VCO 1800-MHz Open Loop Phase Noise = |
|
|
|
Texas Instruments |
1-6000MHz RF Gain Block •1 1 MHz – 6000 MHz • Gain: 17 dB • Noise Figure: 3.5 dB • Output P1dB: 16.5 dBm at 2000 MHz • Output IP3: 28.5 dBm at 2000 MHz • Power Down Mode • Single Supply: 3.3 V • Stabilized Performance Over Temperature • Unconditionally Stable • Robust ESD: |
|
|
|
Texas Instruments |
Dual-Band IQ/IF TRANSCEIVER 1 • Highly Integrated 802.16 d/e Radio IQ/IF Transceiver PLL ASIC • Fully Integrated IF and RF VCOs and Synthesizers • Super Heterodyne Architecture for Superior Performance • Internal PLL Reference Oscillator with Clock Output for Base-Band ASICs • |
|
|
|
Texas Instruments |
DUAL-BAND/DUAL-MODE PCS RECEIVER -locked-loop (PLL) configuration. A state is also available that allows the low-band LO to serve as the high-band LO through a mode-selectable frequency doubler. A wideband mixer is also available for transmit loop architectures commonly used in adva |
|
|
|
Texas Instruments |
Quadrature Modulator •1 High Linearity: – Output IP3: 30 dBm at 1850 MHz • Low Output Noise Floor: –160 dBm/Hz • 78-dBc Single-Carrier WCDMA ACPR at –10-dBm Channel Power • Unadjusted Carrier Suppression: –40 dBm • Unadjusted Sideband Suppression: –45 dBc • Single Supply |
|
|
|
Texas Instruments |
Integer-N PLL •1 Fully Integrated VCO • Low Phase Noise: –137dBc/Hz (at 600kHz, fVCO of 1.9GHz) • Low Noise Floor: –158dBc/Hz at 10MHz Offset • Integer-N PLL • Input Reference Frequency range: 10MHz to 104MHz • VCO Frequency Divided by 2-4 Output • Output Buffer E |
|
|
|
Texas Instruments |
Integer-N PLL •1 Fully Integrated VCO • Low Phase Noise: –137dBc/Hz (at 600kHz, fVCO of 1.9GHz) • Low Noise Floor: –158dBc/Hz at 10MHz Offset • Integer-N PLL • Input Reference Frequency range: 10MHz to 104MHz • VCO Frequency Divided by 2-4 Output • Output Buffer E |
|
|
|
Texas Instruments |
INTEGRATED IQ DEMODULATOR 1 •2 Frequency Range: 1700 MHz to 6000 MHz • Integrated Baseband Programmable-Gain Amplifier • On-Chip Programmable Baseband Filter • High Out-of-Band IP3: 22 dBm at 3550 MHz • High Out-of-Band IP2: 52 dBm at 3550 MHz • Hardware and Software Power Do |
|
|
|
Texas Instruments |
IQ Demodulator 1 •2 Frequency Range: 1.7 GHz to 2 GHz • Integrated Baseband Programmable-Gain Amplifier • On-Chip Programmable Baseband Filter • High Cascaded IP3: 21 dBm at 1.9 GHz • High IP2: 60 dBm at 1.9 GHz • Hardware and Software Power Down • 3-Wire Serial Pr |
|
|
|
Texas Instruments |
Quadrature Modulator • 71-dBc Single-Carrier WCDMA ACPR at –14-dBm Channel Power • P1dB of 7 dBm • Typical Unadjusted Carrier Suppression 35 dBc at 2 GHz • Typical Unadjusted Sideband Suppression 35 dBc at 2 GHz • Very Low Noise Floor • Differential or Single-Ended I, Q |
|
|
|
Texas Instruments |
40-4000 MHz RF Gain Block •1 40 MHz – 4000 MHz • Gain: 15 dB • Noise Figure: 3.8 dB • Output P1dB: 17.5 dBm at 2000 MHz • Output IP3: 32.5 dBm at 2000 MHz • Power Down Mode • Single Supply: 5 V • Stabilized Performance over Temperature • Unconditionally Stable • Robust ESD: > |
|
|
|
Texas Instruments |
Multiple-Standard Fully Integrated 13.56-MHz RFID Analog Front End and Data-Framing Reader System 1 • Completely Integrated Protocol Handling • Separate Internal High-PSRR Power Supplies for Analog, Digital, and PA Sections Provide Noise Isolation for Superior Read Range and Reliability • Dual Receiver Inputs With AM and PM Demodulation to Minimi |
|
|
|
Texas Instruments |
Fully Integrated 13.56-MHz RFID Reader/Writer IC 1 • Completely Integrated Protocol Handling for ISO/IEC 14443 A and B, NFC Forum Device Types 1 to 4, and FeliCa™ • Input Voltage Range: 2.7 VDC to 5.5 VDC • Programmable Output Power: +20 dBm (100 mW) or +23 dBm (200 mW) • Programmable I/O Voltage L |
|