| No. | parte # | Fabricante | Descripción | Hoja de Datos |
|---|---|---|---|---|
|
|
|
Texas Instruments |
3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver •1 ESD Protection for RS-232 Bus Pins – ±15 kV (HBM) – ±8 kV (IEC61000-4-2, Contact Discharge) – ±15 kV (IEC61000-4-2, Air-Gap Discharge) • Meets or Exceeds the Requirements of TIA/EIA232-F and ITU V.28 Standards • Operates With 3-V to 5.5-V VCC Supp |
|
|
|
|
Texas Instruments |
5-V Dual RS-232 Line Driver/Receiver • Meets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standards • ESD protection for RS-232 bus pins: ±15kV human-body model • Operates at 5V VCC supply • Operates up to 120kbit/s • Two drivers and two receivers • Latch-up performance exc |
|
|
|
|
Texas Instruments |
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is set low and EN is high, both drivers and receivers are shut off, an |
|
|
|
|
Texas Instruments |
5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER 1 • ESD Protection for RS-232 I/O Pins – ±15-kV Human-Body Model (HBM) • Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards • Operates at 5-V VCC Supply • Four Drivers and Four Receivers • Operates up to 120 kbit/s • External C |
|
|
|
|
Texas Instruments |
5-V Dual RS-232 Line Driver/Receiver • Meets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standards • ESD protection for RS-232 bus pins: ±15kV human-body model • Operates at 5V VCC supply • Operates up to 120kbit/s • Two drivers and two receivers • Latch-up performance exc |
|
|
|
|
Texas Instruments |
Switched Capacitor Voltage Converter •1 Inverts or Doubles Input Supply Voltage • Narrow SO-8 Package • 6.5-Ω Typical Output Resistance • 88% Typical Conversion Efficiency at 100 mA • Selectable Oscillator Frequency: 10 kHz/80 kHz 2 Applications • Laptop Computers • Cellular Phones • Me |
|
|
|
|
Texas Instruments |
Dual EIA-232 Drivers/Receivers • Meets or exceeds TIA/EIA-232-F and ITU recommendation V.28 • Operates from a single 5V power supply with 1µF charge-pump capacitors • Operates up to 120kbit/s • Two drivers and two receivers • ±30V Input levels • Low supply current: 8mA typical • E |
|
|
|
|
Texas Instruments |
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER 1 •2 Single-Chip and Single-Supply Interface for IBM™ PC/AT™ Serial Port • ESD Protection for RS-232 Bus Pins – ±15-kV Human-Body Model (HBM) – ±8-kV IEC61000-4-2, Contact Discharge – ±15-kV IEC61000-4-2, Air-Gap Discharge • Meets or Exceeds Requirem |
|
|
|
|
Texas Instruments |
3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver •1 Operates With 3-V to 5.5-V VCC Supply • Single-Chip and Single-Supply Interface for IBM™ PC/AT™ Serial Port • RS-232 Bus-Pin ESD Protection of ±15 kV Using Human-Body Model (HBM) • Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU V.28 St |
|
|
|
|
Texas Instruments |
3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver •1 RS-232 Bus-Pin ESD Protection Exceeds ±15 kV Using Human-Body Model (HBM) • Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards • Operates With 3-V to 5.5-V VCC Supply • Operates Up to 250 kbps • Two Drivers and Two Receivers |
|
|
|
|
Texas Instruments |
3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver •1 RS-232 Bus-Terminal ESD Protection Exceeds ±15 kV Using Human-Body Model (HBM) • Meets or Exceeds the Requirements of TIA/EIA232-F and ITU V.28 Standards • Operates With 3-V to 5.5-V VCC Supply • Operates up to 250 kbit/s • Two Drivers and Two Rec |
|
|
|
|
Texas Instruments |
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER 1 • RS-232 Bus-Pin ESD Protection Exceeds ±15 kV Using Human-Body Model (HBM) • Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards • Operates With 3-V to 5.5-V VCC Supply • Operates Up To 250 kbit/s • Two Drivers and Two Receiv |
|
|
|
|
ETCTI |
REF31xx 15ppm/ C Maximum 100- A SOT-23 Series Voltage Reference (Rev. D) |
|
|
|
|
Texas Instruments |
5-V DUAL RS-232 LINE DRIVER/RECEIVER provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 5-V supply. This device operates at data signaling rate |
|
|
|
|
Texas Instruments |
3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER • Controlled Baseline – One Assembly/Test Site, One Fabrication Site • Extended Temperature Performance of –55°C to 125°C • Enhanced Diminishing Manufacturing Sources (DMS) Support • Enhanced Product-Change Notification • Qualification Pedigree (1) |
|
|
|
|
Texas Instruments |
3-V to 5.5-V RS-232 Line Driver/Receiver • RS-232 Bus-pin ESD protection exceeds ±15 kV using human body model (HBM) • Meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28 standards • Operates with 3-V to 5.5-V VCC supply • Operates up to 250 kbps • One driver and one receiver • |
|
|
|
|
Texas Instruments |
3-V to 5.5-V Single-Channel RS-232 Line Driver/Receiver •1 ESD Protection for RS-232 Pins – ±15-kV Human-Body Model (HBM) – ±8 kV (IEC 61000-4-2, Contact Discharge) – ±15 kV (IEC 61000-4-2, Air-Gap Discharge) • Meets or Exceeds the Requirements of TIA/EIA232-F and ITU v.28 Standards • Operates With 3-V to |
|
|
|
|
Texas Instruments |
5-V Multichannel RS-232 Line Driver/Receiver 232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 5-V supply. The devices operate at data signa |
|
|
|
|
Texas Instruments |
SINGLE-CHANNEL SPST ANALOG SWITCH D Low ON-State Resistance (10 W) D ON-State Resistance Flatness (1.5 W) D Control Inputs Are 5.5-V Tolerant D Low Charge Injection (5 pC Max) D 300-MHz −3-dB Bandwidth at 255C D Low Total Harmonic Distortion (THD) (0.05%) D 2-V to 5.5-V Single-Supply |
|
|
|
|
Texas Instruments |
5-V Dual RS-232 Line Driver/Receiver • Meets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standards • ESD protection for RS-232 bus pins: ±15kV human-body model • Operates at 5V VCC supply • Operates up to 120kbit/s • Two drivers and two receivers • Latch-up performance exc |
|
Desde 2024. D4U Semiconductor.
|