| No. | parte # | Fabricante | Descripción | Hoja de Datos |
|---|---|---|---|---|
|
|
|
Philipss |
Dual and single low noise op amp NON –INV INPUT A 2 BALANCE A 3 V – 4 BALANCE B 5 NON –INV B 6 INV B 7 • Small-signal bandwidth: 10MHz • Output drive capability: 600Ω, 10VRMS at VS=±18V • Input noise voltage: 4nVń ǸHz • DC voltage gain: 100000 • AC voltage gain: 6000 at 10kHz • Power |
|
|
|
|
Philipss |
150MHz phase-locked loop an extended supply voltage range and a lower temperature coefficient of the VCO center frequency in comparison with its predecessor, the NE 568. The NE568A is function and pin-compatible with the NE568, requiring only minor changes in peripheral circ |
|
|
|
|
Philipss |
Dual timer • Turn-off time less than 2µs (556-1) • Maximum operating frequency >500kHz (556-1) • Timing from microseconds to hours • Replaces two 555 timers • Operates in both astable and monostable modes • High output current • Adjustable duty cycle • TTL com |
|
|
|
|
Philipss |
Function generator • Wide range of operating voltage (up to 24V; single or dual) • High linearity of modulation • Highly stable center frequency (200ppm/°C typical) • Highly linear triangle wave output • Frequency programming by means of a resistor or capacitor, volta |
|
|
|
|
Philipss |
Addressable peripheral drivers CS A0 A1 A2 Q0 Q1 Q2 Q3 GND 1 2 3 4 5 6 7 8 9 TOP VIEW • 8 high current outputs • Low-loading bus compatible inputs • Power-on clear ensures safe operation • NE590 will operate in addressable or demultiplex mode • Allows random (addressed) data en |
|
|
|
|
Philipss |
Dual timer • Turn-off time less than 2µs (556-1) • Maximum operating frequency >500kHz (556-1) • Timing from microseconds to hours • Replaces two 555 timers • Operates in both astable and monostable modes • High output current • Adjustable duty cycle • TTL com |
|
|
|
|
Philipss |
Quad timer • 100 mA output current per section • Edge-triggered (no coupling capacitor) • Output independent of trigger conditions • Wide supply voltage range 4.5 V to 16 V • Timer intervals from microseconds to hours • Time period equals RC • Military qualific |
|
|
|
|
Philipss |
Active-LOW system reset • High precision threshold detection voltage: • Super low operating supply current: ICCH=1.5 µA typ.; ICCL=1.0 µA typ. APPLICATIONS VS ±3% • Hysteresis voltage: 50 mV typ. • Internal Power-On-Reset Delay time: 20 µs typ. • Detection threshold volt |
|
|
|
|
Philipss |
Tone decoder/phase-locked loop • Wide frequency range (.01Hz to 500kHz) • High stability of center frequency • Independently controllable bandwidth (up to 14%) • High out-band signal and noise rejection • Logic-compatible output with 100mA current sinking capability • Inherent im |
|
|
|
|
Philipss |
Dual and single low noise op amp NON –INV INPUT A 2 BALANCE A 3 V – 4 BALANCE B 5 NON –INV B 6 INV B 7 • Small-signal bandwidth: 10MHz • Output drive capability: 600Ω, 10VRMS at VS=±18V • Input noise voltage: 4nVń ǸHz • DC voltage gain: 100000 • AC voltage gain: 6000 at 10kHz • Power |
|
|
|
|
Philipss |
Dual and single low noise op amp NON –INV INPUT A 2 BALANCE A 3 V – 4 BALANCE B 5 NON –INV B 6 INV B 7 • Small-signal bandwidth: 10MHz • Output drive capability: 600Ω, 10VRMS at VS=±18V • Input noise voltage: 4nVń ǸHz • DC voltage gain: 100000 • AC voltage gain: 6000 at 10kHz • Power |
|
|
|
|
Philipss |
Switched-mode power supply controller GAIN • Micro-miniature (D) package • Pulse width modulator • Current limiting (cycle by cycle) • Sawtooth generator • Stabilized power supply • Double-pulse protection • Internal temperature-compensated reference ORDERING INFORMATION DESCRIPTION 8- |
|
|
|
|
Philipss |
Dual timer • Turn-off time less than 2µs (556-1) • Maximum operating frequency >500kHz (556-1) • Timing from microseconds to hours • Replaces two 555 timers • Operates in both astable and monostable modes • High output current • Adjustable duty cycle • TTL com |
|
|
|
|
Philipss |
Telephone trunk comandor OUTPUT_1 THD_TRIM_1 • Complete compressor and expandor in one IC • Temperature compensated • Greater than 110 dB dynamic range • Operates down to 6 VDC • System levels adjustable with external components • Distortion may be trimmed out APPLICATIONS |
|
|
|
|
Philipss |
Vacuum fluorescent display driver GND • Digit and/or segment drivers • Active output pull –down circuitry • High output breakdown voltage • Low supply voltage • Input compatible with all logic outputs APPLICATIONS D1 Package IN 1 IN 2 IN 3 IN 4 IN 5 IN 6 IN 7 IN 8 GND 1 2 3 4 5 6 7 |
|
|
|
|
Philipss |
Sample-and-hold amplifier of ion-implanted JFETs with bipolar devices to obtain high accuracy, fast acquisition time, and low droop rate. This device is pin-compatible with the LF198, and features superior performance in droop rate and output drive capability. The circuit sho |
|
|
|
|
Philipss |
Sample-and-hold amplifier of ion-implanted JFETs with bipolar devices to obtain high accuracy, fast acquisition time, and low droop rate. This device is pin-compatible with the LF198, and features superior performance in droop rate and output drive capability. The circuit sho |
|
|
|
|
Philipss |
Brushless DC motor controller • 8-bit DAC • Serial-to-parallel converter • Output pre-drivers • Entire switch mode conversion • Adaptable to 60° or 120° commutation • Overcurrent protection APPLICATIONS RESET 4 DAC REFIN 5 22 PHASE 1L 21 PHASE 20 PHASE 2L 19 PHASE 18 PHASE 3L |
|
|
|
|
Philipss |
Quad timer • 100 mA output current per section • Edge-triggered (no coupling capacitor) • Output independent of trigger conditions • Wide supply voltage range 4.5 V to 16 V • Timer intervals from microseconds to hours • Time period equals RC • Military qualific |
|
|
|
|
Philipss |
Active-LOW system reset • High precision threshold detection voltage: • Super low operating supply current: ICCH=1.5 µA typ.; ICCL=1.0 µA typ. APPLICATIONS VS ±3% • Hysteresis voltage: 50 mV typ. • Internal Power-On-Reset Delay time: 20 µs typ. • Detection threshold volt |
|
Desde 2024. D4U Semiconductor.
|