| No. | parte # | Fabricante | Descripción | Hoja de Datos |
|---|---|---|---|---|
|
|
|
Philips |
Low power dual operational amplifi In the linear mode the input common-mode voltage range includes ground and the output voltage can also swing to includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage. The unity g |
|
|
|
|
Philips |
Switched-mode power supply control circuit MODULATOR 5 DUTY CYCLE CONTROL 6 RT 7 • Stabilized power supply • Temperature-compensated reference source • Sawtooth generator • Pulse-width modulator • Remote on/off switching • Current limiting • Low supply voltage protection • Loop fault protec |
|
|
|
|
Philips |
Dual and single low noise op amp NON –INV INPUT A 2 BALANCE A 3 V – 4 BALANCE B 5 NON –INV B 6 INV B 7 • Small-signal bandwidth: 10MHz • Output drive capability: 600Ω, 10VRMS at VS=±18V • Input noise voltage: 4nVń ǸHz • DC voltage gain: 100000 • AC voltage gain: 6000 at 10kHz • Power |
|
|
|
|
Philips |
Sample-and-hold amplifier of ion-implanted JFETs with bipolar devices to obtain high accuracy, fast acquisition time, and low droop rate. This device is pin-compatible with the LF198, and features superior performance in droop rate and output drive capability. The circuit sho |
|
|
|
|
Philips |
Timer • Turn-off time less than 2 µs • Max. operating frequency greater than 500 kHz • Timing from microseconds to hours • Operates in both astable and monostable modes • High output current • Adjustable duty cycle • TTL compatible • Temperature stability |
|
|
|
|
Philips |
Timer • Turn-off time less than 2 µs • Max. operating frequency greater than 500 kHz • Timing from microseconds to hours • Operates in both astable and monostable modes • High output current • Adjustable duty cycle • TTL compatible • Temperature stability |
|
|
|
|
Philips |
Dual timer • Turn-off time less than 2µs (556-1) • Maximum operating frequency >500kHz (556-1) • Timing from microseconds to hours • Replaces two 555 timers • Operates in both astable and monostable modes • High output current • Adjustable duty cycle • TTL com |
|
|
|
|
Philips |
Switched-mode power supply control circuit needed for full-featured switched-mode power supplies. The 100mA source/sink output is designed to drive power FETs directly. The associated output logic is designed to prevent double pulsing or cross-conduction current spiking on the output. All of |
|
|
|
|
Philips |
8-Bit mp-compatible D/A converter • 8-bit resolution • Input latches • Low-loading data inputs • On-chip voltage reference • Output buffer amplifier • Accurate to ± LSB (0.19%) • Monotonic to 8 bits • Amplifier and reference both short-circuit protected • Compatible with 8085, 6800 |
|
|
|
|
Philips |
8-Bit mp-compatible D/A converter • 8-bit resolution • Input latches • Low-loading data inputs • On-chip voltage reference • Output buffer amplifier • Accurate to ± LSB (0.19%) • Monotonic to 8 bits • Amplifier and reference both short-circuit protected • Compatible with 8085, 6800 |
|
|
|
|
Philips |
Quad high-performance operational amplifier –INPUT 2 OUTPUT 2 • Low input bias current: < ±3nA • Low input offset current: < ±3nA • Low input offset voltage:<1mV • Low supply current: 1.5mA/A • 1V/µs slew rate • High input impedance: 100MΩ • High common-mode impedance: 10GΩ • Internal compen |
|
|
|
|
Philips |
Dual and single low noise op amp NON –INV INPUT A 2 BALANCE A 3 V – 4 BALANCE B 5 NON –INV B 6 INV B 7 • Small-signal bandwidth: 10MHz • Output drive capability: 600Ω, 10VRMS at VS=±18V • Input noise voltage: 4nVń ǸHz • DC voltage gain: 100000 • AC voltage gain: 6000 at 10kHz • Power |
|
|
|
|
Philips |
Dual and single low noise op amp NON –INV INPUT A 2 BALANCE A 3 V – 4 BALANCE B 5 NON –INV B 6 INV B 7 • Small-signal bandwidth: 10MHz • Output drive capability: 600Ω, 10VRMS at VS=±18V • Input noise voltage: 4nVń ǸHz • DC voltage gain: 100000 • AC voltage gain: 6000 at 10kHz • Power |
|
|
|
|
Philips |
Switched-mode power supply control circuit FEEDBACK GAIN • Micro-miniature (D) package • Pulse-width modulator • Current limiting (cycle-by-cycle) • Sawtooth generator • Stabilized power supply • Double pulse protection • Internal temperature-compensated reference ORDERING INFORMATION DESCR |
|
|
|
|
Philips |
Dual timer • Turn-off time less than 2µs (556-1) • Maximum operating frequency >500kHz (556-1) • Timing from microseconds to hours • Replaces two 555 timers • Operates in both astable and monostable modes • High output current • Adjustable duty cycle • TTL com |
|
|
|
|
Philips |
Dual timer • Turn-off time less than 2µs (556-1) • Maximum operating frequency >500kHz (556-1) • Timing from microseconds to hours • Replaces two 555 timers • Operates in both astable and monostable modes • High output current • Adjustable duty cycle • TTL com |
|
|
|
|
Philips |
Function generator • Wide range of operating voltage (up to 24V; single or dual) • High linearity of modulation • Highly stable center frequency (200ppm/°C typical) • Highly linear triangle wave output • Frequency programming by means of a resistor or capacitor, volta |
|
|
|
|
Philips |
8-Bit mp-compatible D/A converter • 8-bit resolution • Input latches • Low-loading data inputs • On-chip voltage reference • Output buffer amplifier • Accurate to ± LSB (0.19%) • Monotonic to 8 bits • Amplifier and reference both short-circuit protected • Compatible with 8085, 6800 |
|
|
|
|
Philips |
Wide-band high-frequency amplifier • 600MHz bandwidth • 20dB insertion gain • 4.8dB (6dB) noise figure ZO=75Ω (ZO=50Ω) • No external components required • Input and output impedances matched to 50/75Ω systems • Surface mount package available • MIL-STD processing available • 2000V ES |
|
|
|
|
Philips |
High slew rate operational amplifier • 35V/µs slew rate at unity gain • Pin-for-pin replacement for µA709, µA748, or LM101 • Compensated with a single capacitor ORDERING INFORMATION DESCRIPTION 8-Pin Plastic Dual In-Line Package (DIP) 8-Pin Ceramic Dual In-Line Package (CERDIP) 8-Pin C |
|
Desde 2024. D4U Semiconductor.
|