No. | parte # | Fabricante | Descripción | Hoja de Datos |
---|---|---|---|---|
|
|
ON Semiconductor |
Fan Motor Driver |
|
|
|
ON Semiconductor |
Half-pre Motor Driver Single-Phase Full-Wave Single-phase full-wave drive (15V, 1.5A transistors are built in) Half predriver with integrated high side transistor Built-in variable speed function controlled by an external input The LB11660FV can implement quiet, low-vibration variable speed |
|
|
|
ON Semiconductor |
Three-Phase Brushless Motor Driver • Three-phase bipolar current linear drive + midpoint control circuit. • PLL speed control circuit. • Speed is controlled by an external clock signal. • Supports Hall FG operation. • Built-in output saturation prevention circuit. • Phase lock detecti |
|
|
|
Mitsubishi Electric Semiconductor |
Intelligent Power Module a) Adopting new 5th generation IGBT (CSTBT) chip, which performance is improved by 1µm fine rule process. For example, typical Vce(sat)=1.9V @Tj=125°C b) I adopt the over-temperature conservation by Tj detection of CSTBT chip, and error output is pos |
|
|
|
ON Semiconductor |
Single-Phase Full-Wave Fan Motor Driver • Single-phase full-wave drive (16V, 1.0A transistors are built in) • Built-in variable speed function controlled by a thermistor input The LB11961V can implement quiet, low-vibration variable speed control using externally clocked high side transist |
|
|
|
ON Semiconductor |
2-phase Unipolar Brushless Motor Driver a wide usable voltage range and a minimal number of required external components. It also supports the formation of motor lock protection and automatic recovery circuits. Features • Output protection Zener Diodes with Variable Breakdown Voltages ♦ Wh |
|
|
|
ON Semiconductor |
Stepper Motor Driver • Low saturation voltage forward/reverse motor driver (VO sat = 0.25V at IO = 200mA) • Two H-bridge channels • Wide usable voltage range (Allowable voltage range : 2.5V to 9.5V, absolute maximum rating : 10.5V) • Supports PWM input (Low power consump |
|
|
|
ON Semiconductor |
Three-Phase Brushless Motor Driver r Symbol Conditions Maximum supply voltage VCC max Maximum input current IREG max VREG pin Output current IO max UH, VH, WH, UL, VL, and WL outputs Allowable power dissipation 1 Pd max1 Independent IC Allowable power dissipation 2 Pd m |
|
|
|
Sanyo Semiconductor |
12V Single-phase Bipolar Drive Variable Speed Fan Motor Driver ST !" )H U U ¢£¤¥g(o¦§¨o'§o©© &ª1M«0¬® ¯^i' # &'&( #,, &'&( # #,, Z[\]^ `a\]^ RSR RS RS QS S !" # # # # # #, |
|
|
|
ON Semiconductor |
Low-saturation Forward/Reverse Motor Driver low-saturation outputs in an ultraminiature slim package. The LB1938FA provides forward, reverse, brake, and standby modes controlled by two input signals, and is an optimal DC motor driver for notebook personal computers, digital cameras, cell phone |
|
|
|
ON Semiconductor |
Stepping Motor Driver • PWM current control (fixed OFF time) • Load current digital selector (1-2, W1-2, 2W1-2, 4W1-2 phase exciter drive possible) • Selectable current decay pattern (SLOW DECAY, FAST DECAY, MIX DECAY) • Simultaneous ON prevention function (feed-through c |
|
|
|
ON Semiconductor |
Three-Phase Brushless Motor Driver voltage Output current Allowable power dissipation 1 Symbol VCC max IO max Pd max1 Conditions UH, VH, WH, UL, VL, WL output Independent IC Allowable power dissipation 2 Pd max2 Mounted on a circuit board* Operating temperature Topr Storage te |
|
|
|
ON Semiconductor |
Direct PWM Drive Brushless Motor Predriver Three-phase bipolar drive Direct PWM drive (controlled either by control voltage or PWM variable duty pulse input) Built-in forward/reverse switching circuit Start/stop mode switching circuit (stop mode power saving function) Built-in input |
|
|
|
ON Semiconductor |
Microprocessor Fan Motor Interface Driver • Fan motor interface driver function (FGIN) ⇒ This IC accepts a signal from a microcontroller and interfaces to external power transistors (PMOS and NMOS) to provide high-efficiency low-power single-phase full-wave drive. • Variable speed input pin |
|
|
|
ON Semiconductor |
Three-in-One Motor Driver at Ta = 25°C Parameter Symbol Conditions IC power source voltage VCC max Motor power source 1 Motor power source 2 Motor power source 2 Applied input voltage CVCO max DVCO max LVCO max VI1 max Motor output current1 ICOUT max Peak current |
|
|
|
ON Semiconductor |
Two-Phase Brushless Motor Driver • Hall Elements can be Connected Directly to the IC itself • 1.5-A Output Current Output Transistors Built in • Rotation Detection Function that Provides a Low-level Output during Motor Drive and a High-level Output when the Motor is Stopped • Motor |
|
|
|
ON Semiconductor |
Low-voltage/Low-saturation Bidirectional Constant-Voltage Regulated Motor Driver |
|
|
|
Fairchild Semiconductor |
12-Digit TelephoneCalculator Display .2 30 32 20:1 70 100 -20 -20 50/60 50k 12.0 2.4 1000 10 150 150 60 ao 50 VRMS VRMS Hz p,A ms ms °C °C °C/RH hrs mV Note Display may be operated beyond these limits for short periods of time. Extended periods of operation at high temperatures an |
|
|
|
ON Semiconductor |
Three-Phase Brushless Motor Driver • Three-phase bipolar drive (30V, 2.5V) • Direct PWM drive • Built-in low side inductive kickback absorbing diode • Speed discriminator + PLL speed control • Speed locked state detection output • Built-in forward/reverse switching circuit • Full comp |
|
|
|
ON Semiconductor |
Bidirectional Motor Driver fied board * Operating temperature Topr Storage temperature Tstg * Specified board: 20mm × 30mm × 1.6mm, glass epoxy board. Ratings -0.3 to +10.5 -0.3 to +10.5 VS+VSF -0.3 to +10 1.0 550 800 -20 to +75 -40 to +125 Unit V V V V A mW mW °C °C S |
|