| No. | parte # | Fabricante | Descripción | Hoja de Datos |
|---|---|---|---|---|
|
|
|
Sanyo Semiconductor |
LA4135 |
|
|
|
|
Sanyo Semiconductor |
2.5 - 6 Volt / 2-Channel |
|
|
|
|
Sanyo Semiconductor |
(LA4200 / LA4201) 1.5 - 2.5 W AF |
|
|
|
|
ON Semiconductor |
Power Amplifier • Built-in 2 Channels (Dual) Enabling Use in Stereo and Bridge Amplifier Applications. Dual : 6 W × 2 (typ) Bridge : 19 W (typ) • Minimum Number of External Parts Required • Small Pop Noise at the Time of Power Supply ON/OFF and Good Starting Balance |
|
|
|
|
Sanyo Semiconductor Corporation |
5.5W |
|
|
|
|
ON Semiconductor |
Audio Power Amplifier High-power 2-channel AF power amplifier Low distortion Minimum number of external parts required (no bootstrap capacitor required) Low pop noise at the time of power supply ON/OFF Good ripple rejection (58dB typ) Wide operating voltage ra |
|
|
|
|
Sanyo Semiconductor |
2.7W AF |
|
|
|
|
SANYO Semiconductors |
5 W Two-Channel AF Power Amplifier max Topr Tstg With no input signal Per channel With an infinitely large heat sink Conditions Rated value 24 2 15 150 –20 to +75 –40 to +150 Unit V A W °C °C °C Operating Conditions at Ta = 25°C Parameter Recommended supply voltage Recommended load r |
|
|
|
|
ON Semiconductor |
2-Channel 26V Power Amplifier Two channels in a single package PO = 12W2 (VCC = 26.4V, RL = 8, THD = 10%) PO = 20W2 (VCC = 26.4V, RL = 4, THD = 10%) Can drive 4 speakers Built-in standby switch Minimizes impulse noises Functions Standby switch (active on high ( |
|
|
|
|
ON Semiconductor |
Power Amplifier • Low current drain. • 16Ω load drive capability. • Excellent reduced voltage characteristics. • Excellent power supply ripple rejection. • Minimum number of external parts required (no input capacitor, feedback capacitor required). • Less harmonic i |
|
|
|
|
Sanyo Semiconductor |
1W AF |
|
|
|
|
ON Semiconductor |
20W 2-Channel BTL Power Amplifier an extended low band roll-off frequency provided by a newly-developed NF circuit that does not require an external capacitor. Furthermore, crosstalk, which can cause muddiness in the audio output, has been significantly reduced by both circuit and wi |
|
|
|
|
Sanyo Semiconductor |
(LA4200 / LA4201) 1.5 - 2.5 W AF |
|
|
|
|
ON Semiconductor |
5W Power Amplifier |
|
|
|
|
IK Semiconductor |
Switch Mode Power Supply IC • • • • • • • Fold - back characteristics provides overload protection for external components Burst operation under secondary short - circuit condition implemented Protection against open or short of the control loop Switch - off if line voltage is |
|
|
|
|
ON Semiconductor |
2-channel 13.5W BTL Audio Power Amplifier an extended low band roll-off frequency provided by a newly-developed NF circuit that does not require an external capacitor. Furthermore, crosstalk, which can cause muddiness in the audio output, has been significantly reduced by both circuit and wi |
|
|
|
|
ON Semiconductor |
2-channel 30W BTL Audio Amplifier an extended low band roll-off frequency provided by a newly-developed NF circuit that does not require an external capacitor. Furthermore, crosstalk, which can cause muddiness in the audio output, has been significantly reduced by both circuit and wi |
|
|
|
|
ON Semiconductor |
5W Power Amplifier |
|
|
|
|
Sanyo Semiconductor |
LA4400 / 4.5W Typ |
|
|
|
|
IK Semiconductor |
Baseband Delay Line • Two comb filters, using the switched-capacitor technique, for one line delay time (64 µS) • 3 MHz internal clock signal derived from a 6 MHz CCO, line-locked by the sandcastle pulse (64 µS line) • Comb filtering functions for NTSC colour-difference |
|
Desde 2024. D4U Semiconductor.
|