Joy-IT KY- Hoja de datos

No.	parte #	Fabricante	Descripción
1	KY-013	Joy-IT	Temperature-Sensor module odule provides a NTC thermistor - it will have a lower resistant on higher temperatures. Export: 16.06.2017 Copyright by Joy-IT - Published under CC BY-NC-SA 3.0 Page 54 of 214 KY-013 Temperature-Sensor module You can draw near to the resistant
2	KY-039	Joy-IT	Heartbeat sensor module the photo transistor you can detect the pulse at the signal out. The explanation of the functionality of a photo transistor is simple: It works like a normal transistor - you will detect a higher electricity if the control voltage is higher. Instead
3	KY-018	Joy-IT	Photoresistor module creases its resistance at brighter surrounding. You can determine the resistance of the resistor by using a voltage divider, where a known voltage will be divided between a known and an unknown variable resistor. You can calculate the resistance with
4	KY-003	Joy-IT	Hall Magnetic Field Sensor l Magnetic Field Sensor 3. CODE EXAMPLE ARDUINO This is an example program that lights up an LED when a signal is detected on the sensor. The KY-011, KY016 or KY-029 modules can also be used as LEDs, for example. You can download the code example her
5	KY-038	Joy-IT	Microphone sound sensor module ............................................................................ 4 Picture Technical data / Short description Digital Out: You can use a potentiometer to configure an extreme value for the sonic. IF the value exceeds the extreme value it
6	KY-037	Joy-IT	Microphone sensor module ...................................................................................................... 4 Picture Technical data / Short description Digital Out: You can use a potentiometer to configure an extreme value for the sonic. If the value ex
7	KY-025	Joy-IT	Reed module ...................................... 5 Picture Technical data / Short description If a magnetic field was detected, it will be shown at the digital output. Export: 16.06.2017 Copyright by Joy-IT - Published under CC BY-NC-SA 3.0 Page 111 of 214
8	KY-033	Joy-IT	Tracking sensor module ea is in front of it. It shows which of the 2 areas it is via digital output, as you can see in the picture below. The Sensitivity (minimum range) of the sensor can be adjusted by the controller. This behavior can be used to automatically follow a li
9	KY-016	Joy-IT	RGB 5mm LED module onnected by a common cathode. An additional resistor might be necessary for some voltages. Vf [Red]= 1,8V Vf [Green,Blue]= 2,8V If= 20mA Vorwiderstände: Export: 16.06.2017 Copyright by Joy-IT - Published under CC BY-NC-SA 3.0 Page 65 of 214 KY-0
10	KY-026	Joy-IT	Flame-sensor module ...................................................... 4 Picture Technical data / Short description The connected photo diode is sensitive to the spectral range of light, which is created by open flames. Digital Out: After detecting a flame, a signa
11	KY-035	Joy-IT	Bihor magnetic sensor module nt magnetic field, near to the sensor. Export: 16.06.2017 Copyright by Joy-IT - Published under CC BY-NC-SA 3.0 Page 154 of 214 KY-035 Bihor magnetic sensor module Pinout Code example Arduino The program measures the current voltage value at the
12	KY-009	Joy-IT	RGB LED SMD module connected with a common cathode. A resistor is necessary for different voltages. Vf [Red]= 1,8V Vf [Green,Blue]= 2,8V If= 20mA Pre-resistor: Export: 16.06.2017 Copyright by Joy-IT - Published under CC BY-NC-SA 3.0 Page 37 of 214 KY-009 RGB LED
13	KY-006	Joy-IT	Passiv Piezo-Buzzer module to create different sounds from the Piezo-Buzzer. Export: 16.06.2017 Copyright by Joy-IT - Published under CC BY-NC-SA 3.0 Page 34 of 214 KY-006 Passiv Piezo-Buzzer module Pinout Code example Arduino This is an example program which will start
14	KY-040	Joy-IT	Rotary encoder ..................................................... 4 Picture Technical data / Short description The current position of the rotary switch will be send encoded to the output. Encoding The idea of the rotary switch is that with every "step" only on
15	KY-023	Joy-IT	Joystick module as an analog voltage at the output pin. In this joystick, the x-axis and the y-axis have their own potentiometer. Together, they build a voltage devider like the one in the next picture. Export: 16.06.2017 Copyright by Joy-IT - Published under CC B
16	KY003	Joy-IT	Hall Magnetic Field Sensor
17	KY-010	Joy-IT	Light barrier-module f the optical barrier is beeing interrupted. Export: 16.06.2017 Copyright by Joy-IT - Published under CC BY-NC-SA 3.0 Page 43 of 214 KY-010 Light barrier-module Pinout Code example Arduino In this program, a LED will flash up, if a signal was de
18	KY-019	Joy-IT	5V Relais module oltages via 5V output. !!!!! Caution !!!!! Working with voltages over 30V and a main voltage (230V) can harm your body or kill you. We advise you not to work with higher valtages unless you have the needed experience. !!!!! Caution !!!!! The output
19	KY-031	Joy-IT	Knock-sensor module connected. Export: 16.06.2017 Copyright by Joy-IT - Published under CC BY-NC-SA 3.0 Page 140 of 214 KY-031 Knock-sensor module Pinout Code example Arduino This example will light up a LED after the sensor detected a knock or vibration. The modu
20	KY-022	Joy-IT	Infrared receiver module ........................................................ 4 5.2 Lirc Installation ........................................................................................................................................... 4 5.3 IR-Receiver Test ......