| No. | parte # | Fabricante | Descripción | Hoja de Datos |
|---|---|---|---|---|
|
|
|
ETC |
10/100BASE-Tx Magnetics Module |
|
|
|
|
ETC |
QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries • Multiple charge termination methods include: Voltage slope Maximum temperature Charge timer Four stage charge sequence: Soft start charge Fast charge Topping charge Maintenance charge Reverse-pulse charging available in all charge stages Four progr |
|
|
|
|
ETC |
High-Reliablility CA3000 Slash-Series Linear ICs |
|
|
|
|
ETC |
PIP IV Advanced SOPHISTICUS High-End Picture-In-Picture ICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Block Diagram . . . . . . . . . . . |
|
|
|
|
STMicroelectronics |
SERIAL INTERFACE CODEC/FILTER The encode portion of each device consists of an input gain adjust amplifier, an active RC pre-filter which eliminates very high frequency noise prior to entering a switched-capacitor band-pass filter that rejects signals below 200 Hz and above 3400 |
|
|
|
|
Texas Instruments |
IEEE 1394-a Consumer Electronics Link Layer Controller • DTCP content protection (TSB42AA4 only). A separate document explains the DTCP hardware errata for TSB42AA4. It is available upon request to DTLA licensees only. • Interfaces directly to industry standard 400-, 200-, and 100-Mbps physical layer dev |
|
|
|
|
ETC |
Connector Modules with Intergrated LAN Magnetics |
|
|
|
|
ETC |
GRAPHICS PROCESSING IC PROVIDING HIGH QUALITY IMAGES FOR LCD MONITORS |
|
|
|
|
STMicroelectronics |
SERIAL INTERFACE CODEC/FILTER The encode portion of each device consists of an input gain adjust amplifier, an active RC pre-filter which eliminates very high frequency noise prior to entering a switched-capacitor band-pass filter that rejects signals below 200 Hz and above 3400 |
|
|
|
|
ETC |
10/100BASE-T Quad Ports Magnetics Module |
|
|
|
|
ETC |
QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries • Multiple charge termination methods include: Voltage slope Temperature slope Maximum temperature Charge timer • Four stage charge sequence: Soft start charge Fast charge Topping charge Maintenance charge • Reverse-pulse charging available in all ch |
|
|
|
|
ETC |
Pulsed Avionics 1030/1090 MHz cy Load Mismatch Tolerance Emitter to Base Breakdown Collector to Emitter Breakdown DC - Current Gain Thermal Resistance TEST CONDITIONS F = 1030 - 1090 MHz Vcc = 36 Volts PW = Note 1 DF = Note 1 F = 1030 MHz Ie = 20 mA Ic = 20 mA Ic = 20 mA, Vce = 5 |
|
|
|
|
ETC |
10/100 PC Card Lan Magnetics Solutions l l l l l Page : 1/1 Half port and single port designs for maximum layout flexibility . Low profile packages from 0.094 Inch(2.39mm) to 0.078 Inch(1.98mm) for PC card and card bus applications . Compatible package with INTEL,TDK,QSI, and ICS Transf |
|
|
|
|
ETC |
10/100BASE-Tx Magnetics Module |
|
|
|
|
Texas Instruments |
IEEE 1394a-2000 CONSUMER ELECTRONICS • 1394 Features – Integrated 400/200/100 Mbps 2-Port PHY – Compliant to IEEE 1394-1995 and IEEE 1394a-2000 Standards – Supports Bus Manager Functions and Automatic 1394 Self-ID Verification – Separate Asyncchronous Ack FIFOs Decrease the Ack-Tracking |
|
|
|
|
ETC |
Connector Modules with Intergrated LAN Magnetics |
|
|
|
|
ETC |
Signetics Microcontroller Products |
|
|
|
|
ETC |
Typical Performance Characteristics |
|
|
|
|
ETC |
Typical Performance Characteristics |
|
|
|
|
Tyco Electronics |
5 - 40 MHz E-Series RF 16:1 Transformer * 16:1 Impedance Ratio * CT on Secondary ETC16-1T-2 SM-22 Specifications @ 25°C Frequency Range Insertion Loss 5 - 40 MHz 22 MHz 5 - 40 MHz Maximum 1 dB 0.8 dB Amplitude Imbalance 5 - 40 MHz Phase Imbalance 5 - 40 MHz Maximum 0.3 dB Maximum 3° |
|
Desde 2024. D4U Semiconductor.
|