No. | parte # | Fabricante | Descripción | Hoja de Datos |
---|---|---|---|---|
|
|
Texas Instruments |
Dual 4.16Gbps FPD-Link3 Deserializer Hub • AEC-Q100 qualified for automotive applications – Device temperature grade 2: –40℃ to +105℃ ambient operating temperature range • Dual deserializer hub aggregates one or two active sensors over FPD-Link III interface • Power-Over-Coax (PoC) compatib |
|
|
|
ETCTI |
4.25-Gbps 2:1/1:2 CML MUX/Buffer |
|
|
|
ETCTI |
6.0 Gbps HDMI DisplayPort 2:1/1:2 Differential Switch (Rev. D) |
|
|
|
Texas Instruments |
Low-Power 12.5-Gbps 8-Channel Repeater 1 •2 Proven System Interoperability • Comprehensive multi-protocol Repeater Family • Low 65-mW/Channel (Typ) Power Consumption, With Option to Power Down Unused Channels • Transparent Management of Link Training Protocol for PCIe and SAS • Advanced S |
|
|
|
Texas Instruments |
Low Power 28 Gbps 8 Channel Linear Repeater •1 Octal-Channel Multi-Protocol Linear Equalizer Supporting up to 28-Gbps Interfaces • Low Power Consumption: 93 mW and Channel (Typical) • No Heat Sink Required • Linear Equalization for Seamless Support of CR4/KR4 Link Training • Extends Channel Re |
|
|
|
ETC |
155Mbps / 2Km / 1x9 SC Duplex Optical Transceiver Module for Fast Ethernet / ATM / SONET/SDH STM-1/OC-3 Full Compliance with the Optical Performance Requirements of the ATM 100Mbps and 100 Base-FX Version of IEEE 802.3u. Industry Standard 1x9 Footprint and Duplex SC Connector Interface. Single 5V OPT-155A1H1A or 3.3V OPT-155A2H1A Power Supply. PECL Dif |
|
|
|
Texas Instruments |
USB 2.0 High-Speed (480 Mbps) and Audio Switches 1 • High-Speed USB Switch: – 4 Ω RDSON Typical – 12.5 pF CON Typical – 650-MHz Bandwidth ( –3 dB) • Audio Switch: – 3 Ω RDSON Typical – Negative Rail Capability – Low THD: <0.05% – Internal Shunt Resistors for Click-and-Pop Reduction – Powered From VA |
|
|
|
Texas Instruments |
3Gbps HD/SD SDI Low Power Reclocker 1 •2 SMPTE ST 424, SMPTE ST 292, and SMPTE ST 259-C Compliant • Supports 125 Mbps, 270 Mbps, 1.4835 Gbps, 1.485 Gbps, 2.967 Gbps, and 2.97 Gbps Serial Data Rate Operation • Supports DVB-ASI at 270 Mbps and MADI at 125 Mbps • 100 mW Typical Power Cons |
|
|
|
ETCTI |
Two Channel SATA 3-Gbps Redriver* |
|
|
|
Texas Instruments |
USB TYPE-C DP Alt Mode 8.1 Gbps Sink-Side Linear Redriver Crosspoint Switch •1 USB Type-C™ crosspoint switch supporting – USB 3.1 Gen 1 + 2 DP 1.4 lanes – 4 DP 1.4 lanes • USB 3.1 Gen 1 up to 5 Gbps • DisplayPort 1.4 up to 8.1 Gbps (HBR3) • VESA DisplayPort™ alt mode UFP_D redriving crosspoint switch supporting c, d, and e p |
|
|
|
Texas Instruments |
25-Gbps Multi-Rate 2-Channel Retimer 3 Description • Dual-channel multi-rate retimer with integrated signal conditioning • All channels lock independently from 19.6 to 25.8 Gbps (including sub-rates, such as 12.16512 Gbps, 9.8304 Gbps, 6.144 Gbps, and more) • Ultra-low latency: <500 p |
|
|
|
ETCTI |
DS25CP152 3.125 Gbps LVDS 2x2 Crosspoint Switch (Rev. D) |
|
|
|
ETCTI |
2.5 Gbps / 5.0 Gbps / 8.0 Gbps 1 Lane PCI Express Repeater With Equalization and De-Emphasis (Rev. G) |
|
|
|
ETCTI |
DS92UT16 UTOPIA-LVDS Bridge for 1.6 Gbps Bi-directional Data Transfers (Rev. E) |
|
|
|
ETC |
155Mbps / 2Km / 1x9 SC Duplex Optical Transceiver Module for Fast Ethernet / ATM / SONET/SDH STM-1/OC-3 Full Compliance with the Optical Performance Requirements of the ATM 100Mbps and 100 Base-FX Version of IEEE 802.3u. Industry Standard 1x9 Footprint and Duplex SC Connector Interface. Single 5V OPT-155A1H1A or 3.3V OPT-155A2H1A Power Supply. PECL Dif |
|
|
|
ETCTI |
4.25Gbps Transimpedance Amplifier with AGC and RSSI |
|
|
|
ETCTI |
1.6 Gbps To 2.5 Gbps Transceiver (Rev. B) |
|
|
|
ETCTI |
TLK2711-SP 1.6-Gbps to 2.5-Gbps Class V Transceiver (Rev. O) |
|
|
|
Texas Instruments |
Low-Latency Low-Power 10/100Mbps Industrial Ethernet PHY • Low and deterministic latency – TX latency: 40 ns, RX latency: 170 ns – Deterministic latency over power cycles < ±2 ns – Fixed phase XI to TX_CLK relationship < ±2 ns • Robust and small system solution – Integrated circuitry for enhanced EMC – IEC |
|
|
|
Texas Instruments |
2.5Gbps / 5.0Gbps 4 Lane PCI Express Repeater 1 •2 Input and Output signal conditioning increases PCIe reach in backplanes and cables • 0.09 UI of residual deterministic jitter at 5Gbps after 42” of FR4 (with Input EQ) • 0.11 UI of residual deterministic jitter at 5Gbps after 7m of PCIe Cable (w |
|