No. | parte # | Fabricante | Descripción | Hoja de Datos |
---|---|---|---|---|
|
|
ETC |
2SA968A |
|
|
|
ETC |
Sensor Module z Mega pixel CMOS image sensor, OV9653 z Sensor array 1300x1028pixels z lens format: 1/4” z support SXGA,VGA,QVGA,CIF,QCIF z VGA 30fps, QVGA 60fps, QCIF 120fps z Raw RGB, GRB422, YUV422 format z Small size : 41 x 31 mm z Built-in Len (Optional) z P |
|
|
|
ETC |
Fensterdiskriminator-IS |
|
|
|
ETC |
Power Management Unit comparing to the traditional 1A output current at 5V of from a solution that needs a micro-controller which normally consumes Li-Ion battery input voltage, while the up to 1mA current. charger can charge up to 1A of current from an AC adapter i |
|
|
|
Texas Instruments |
Dual High-Speed Differential Line Driver • Meets or exceeds ANSI standard EIA/TIA-422-B • Operates from a single 5V power supply • Drives loads as low as 50Ω up to 15Mbps • TTL- and CMOS-input compatibility • Output short-circuit protection • Interchangeable with DS9638 2 Applications • Fac |
|
|
|
Texas Instruments |
Dual Differential Line Receiver • Meets or exceeds the requirements of ANSI standards EIA/TIA-422-B and EIA/TIA-423-B and ITU recommendations V.10 and V.11 • Operates From Single 5V power supply • Wide common-mode voltage range • High input impedance • TTl-compatible outputs • High |
|
|
|
Texas Instruments |
DUAL HIGH-SPEED DIFFERENTIAL LINE DRIVER g 15 Mbps in properly designed systems. The uA9637A dual line receiver is commonly used as the receiver. For even faster switching speeds in the same pin configuration, see the SN75ALS191. The uA9638C is characterized for operation from 0°C to 70°C. |
|
|
|
Texas Instruments |
DUAL LINE DRIVER d for operation from 0°C to 70°C. logic symbol† logic diagram W-S 1 [Slew-Rate] 2 1A 3 2A 7 1Y 6 2Y † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 1A 2 W-S 1 2A 3 7 1Y 6 2Y Please be aware that an impo |
|
|
|
Texas Instruments |
Dual Differential Line Receiver • Meets or exceeds the requirements of ANSI standards EIA/TIA-422-B and EIA/TIA-423-B and ITU recommendations V.10 and V.11 • Operates From Single 5V power supply • Wide common-mode voltage range • High input impedance • TTl-compatible outputs • High |
|
|
|
Texas Instruments |
DUAL HIGH-SPEED DIFFERENTIAL LINE DRIVER 1 •2 Meets or Exceeds ANSI Standard EIA/TIA-422-B • Operates From a Single 5-V Power Supply • Drives Loads as Low as 50 Ω up to 15 Mbps • TTL- and CMOS-Input Compatibility • Output Short-Circuit Protection • Interchangeable With National Semiconducto |
|
|
|
Texas Instruments |
Level-Translating FM+ I2C Bus Repeater • Two-channel bidirectional I2C buffer • Support for standard mode, fast mode (400kHz), and fast mode+ (1MHz) I2C operation • Operating supply voltage range of 0.8V to 5.5V on A-side • Operating supply voltage range of 2.2V to 5.5V on B-side • Voltag |
|
|
|
Texas Instruments |
DUAL DIFFERENTIAL LINE RECEIVER 3 2OUT † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor pr |
|
|
|
Texas Instruments |
DUAL DIFFERENTIAL LINE RECEIVER 3 2OUT † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor pr |
|
|
|
Texas Instruments |
DUAL LINE DRIVER d for operation from 0°C to 70°C. logic symbol† logic diagram W-S 1 [Slew-Rate] 2 1A 3 2A 7 1Y 6 2Y † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 1A 2 W-S 1 2A 3 7 1Y 6 2Y Please be aware that an impo |
|
|
|
Texas Instruments |
Bus Repeater •1 Two-Channel Bidirectional I2C Buffer • Support for Standard Mode, Fast Mode (400 kHz), and Fast Mode+ (1 Mhz) I2C Operation • Operating Supply Voltage Range of 0.8 V to 5.5 V on A-Side • Operating Supply Voltage Range of 2.2 V to 5.5 V on B-Side • |
|