logo

AN1096 Microchip Using the C30 Compiler to Interface SPI Serial EEPROMs Datasheet


Microchip
AN1096
Part Number AN1096
Manufacturer Microchip (https://www.microchip.com/)
Description The purpose of the program is to show individual features of the SPI protocol and give code samples of the instructions and addressing schemes so that the basic building blocks of a program can be shown. The firmware performs the following operations: • • • • • • Low-Density Byte Write Low-Density B...
Features are not used in the examples provided. INTRODUCTION The 25XXX series serial EEPROMs from Microchip Technology are SPI compatible and have maximum clock frequencies ranging from 3 MHz to 20 MHz. Many times when designing an application which utilizes a serial EEPROM device, it may be beneficial to use a microcontroller which does not feature a dedicated protocol-specific serial port. This can be due to several possible reasons, including size restrictions or costs. In these instances, it is required of the designer to write software routines capable of generating the proper signals for communi...

Document Datasheet AN1096 datasheet pdf (328.70KB)




AN1096 Distributor






AN1096 Similar Datasheet

Part Number Description
AN1001
manufacturer
Vishay Siliconix
The Next Step in Surface-Mount Power MOSFETs
www.DataSheet4U.com AN1001 Vishay Siliconix LITTLE FOOTR TSSOP-8 The Next Step in Surface-Mount Power MOSFETs Wharton McDaniel and David Oldham When Vishay Siliconix introduced its LITTLE FOOT MOSFETs, it was the first time that power MOSFETs had been offered in a true surface-mount package, the SOIC. LITTLE FOOT immediately found a home in new small form factor disk drives, computers, and cellular phones. This is the low profile demanded by applications such as PCMCIA cards. It reduces the power package to the same height as many resistors and capacitors in 0805 and 0605 sizes. It also allows placement on the “passive” side of the PC board. The standard pinouts of the LITTLE FOOT TSSOP-...
AN1003
manufacturer
Littelfuse
Thyristors
Teccor® brand Thyristors AN1003 Introduction Due to high-volume production techniques, Thyristors are now priced so that almost any electrical product can benefit from electronic control. A look at the fundamentals of SCR and Triac phase controls shows how this is possible. Output Power Characteristics Phase control is the most common form of Thyristor power control. The Thyristor is held in the off condition -- that is, all current flow in the circuit is blocked by the Thyristor except a minute leakage current. Then the Thyristor is triggered into an “on” condition by the control circuitry. For full-wave AC control, a single Triac or two SCRs connected in inverse parallel may be used. One of...
AN101
manufacturer
Vishay Siliconix
MOSFETs
...
AN103
manufacturer
Siliconix
The FET Constant-Current Source/Limiter
www.DataSheet4U.com AN103 The FET Constant-Current Source/Limiter Introduction The combination of low associated operating voltage and high output impedance makes the FET attractive as a constant-current source. An adjustable-current source (Figure 1) may be built with a FET, a variable resistor, and a small battery. For optimum thermal stability, the FET should be biased near the zero temperature coefficient point. D S RL RS – + A change in supply voltage or a change in load impedance, will change ID by only a small factor because of the low output conductance goss. DID = (DVDS)(goss) (3) The value of goss is an important consideration in the accuracy of a constant-current source where...
AN1042
manufacturer
ON Semiconductor
High Fidelity Switching Audio Amplifiers Using TMOS Power MOSFETs
AN1042/D High Fidelity Switching Audio Amplifiers Using TMOS Power MOSFETs Prepared by: Donald E. Pauly ON Semiconductor Special Consultant http://onsemi.com APPLICATION NOTE With the introduction of complementary bipolar power transistors in the late 1960s, switching amplifiers became theoretically practical. At low frequencies, bipolar transistors have switching efficiencies of 99% and will directly drive a low impedance speaker filter. The requirement for switching frequencies above 100 kHz resulted in excessive losses however. Bipolar drive circuitry was also complex because of its large base current requirement. With the advent of complementary (voltage/current ratings) TMOS power MOSF...
AN1042D
manufacturer
ON Semiconductor
High Fidelity Switching Audio Amplifiers Using TMOS Power MOSFETs
AN1042/D High Fidelity Switching Audio Amplifiers Using TMOS Power MOSFETs Prepared by: Donald E. Pauly ON Semiconductor Special Consultant http://onsemi.com APPLICATION NOTE With the introduction of complementary bipolar power transistors in the late 1960s, switching amplifiers became theoretically practical. At low frequencies, bipolar transistors have switching efficiencies of 99% and will directly drive a low impedance speaker filter. The requirement for switching frequencies above 100 kHz resulted in excessive losses however. Bipolar drive circuitry was also complex because of its large base current requirement. With the advent of complementary (voltage/current ratings) TMOS power MOSF...
AN1043
manufacturer
Microchip
Unique Features of the MCP23X08/17 GPIO Expanders
The I/O port is highly configurable for maximum flexibility. Figure 1 is a simplified block diagram of an I/O port pin. The port can either drive logic levels on the pin, or read logic levels from the pad. The level on the pad can be read at any time, regardless if the pin is configured as an input or an output. The IODIR register controls the direction of the pins (input or output). More specifically, the IODIR registers simply enables/disables the output driver. When the driver is activated (IODIR = 0), the pad is driven to the state in the latch register (OLAT). When deactivated (IODIR = 1), the driver is high impedance. The I/O port has multiple, individual configurations. Each pin can …...
AN1048
manufacturer
ON Semiconductor
RC Snubber Networks
AN1048/D RC Snubber Networks For Thyristor Power Control and Transient Suppression By George Templeton Thyristor Applications Engineer http://onsemi.com APPLICATION NOTE INTRODUCTION Edited and Updated RC networks are used to control voltage transients that could falsely turn-on a thyristor. These networks are called snubbers. The simple snubber consists of a series resistor and capacitor placed around the thyristor. These components along with the load inductance form a series CRL circuit. Snubber theory follows from the solution of the circuit’s differential equation. Many RC combinations are capable of providing acceptable performance. However, improperly used snubbers can cause unrel...
AN1048D
manufacturer
ON Semiconductor
RC Snubber Networks
AN1048/D RC Snubber Networks For Thyristor Power Control and Transient Suppression By George Templeton Thyristor Applications Engineer http://onsemi.com APPLICATION NOTE INTRODUCTION Edited and Updated RC networks are used to control voltage transients that could falsely turn-on a thyristor. These networks are called snubbers. The simple snubber consists of a series resistor and capacitor placed around the thyristor. These components along with the load inductance form a series CRL circuit. Snubber theory follows from the solution of the circuit’s differential equation. Many RC combinations are capable of providing acceptable performance. However, improperly used snubbers can cause unrel...
AN105
manufacturer
Vishay Siliconix
FETS AS VOLTAGE-CONTROLLED RESISTORS
www.DataSheet4U.com AN105 FETs As VoltageĆControlled Resistors Introduction: The Nature of VCRs A voltage-controlled resistor (VCR) may be defined as a three-terminal variable resistor where the resistance value between two of the terminals is controlled by a voltage potential applied to the third. For a junction field-effect transistor (JFET) under certain operating conditions, the resistance of the drain-source channel is a function of the gate-source voltage alone and the JFET will behave as an almost pure ohmic resistor. Maximum drain-source current, IDSS, and minimum resistance rDS(on), will exist when the gate-source voltage is equal to zero volts (VGS = 0). If the gate voltage is in...




logo    Since 2024. D4U Semiconductor.   |   Contact Us   |   Privacy Policy