logo

SP8852E Zarlink Semiconductor 1.7GHz PARALLEL LOAD PROFESSIONAL SYNTHESISER Datasheet

SP8852E/IG/HCAR PLL FREQUENCY SYNTHESIZER, BIPOL


Zarlink Semiconductor
SP8852E
Part Number SP8852E
Manufacturer Zarlink Semiconductor
Description These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these p...
Features s 2
·7 GHz Operating Frequency s Single 5V Supply HC44 s Low Power Consumption <1
·3W s High Comparison Frequency : 20MHz s High Gain Phase Detector : 1mA/rad *FPD and FREF outputs are reversed by the phase www.DataSheet4U.com s Zero ‘Dead Band’ Phase Detector detector sense bit in the F1/F2 programming word, bit 12. The above diagram is correct when bit 12 is high. s Wide Range of RF and Reference Division Ratios s Programming by Dual Word Data Transfer Fig. 1 Pin connections - top view ABSOLUTE MAXIMUM RATINGS Supply voltage Operating temperature Storage temperature Prescaler and reference in...

Document Datasheet SP8852E datasheet pdf (250.36KB)
Distributor Distributor
DigiKey
Stock 376 In Stock
Price
7 units: 46.02 USD
BuyNow BuyNow BuyNow (Manufacturer a Zarlink Semiconductor Inc)




SP8852E Distributor

Zarlink Semiconductor Inc
SP8852E/IG/HCAR
PLL FREQUENCY SYNTHESIZER, BIPOL
7 units: 46.02 USD
Distributor
DigiKey

376 In Stock
BuyNow BuyNow
Zarlink Semiconductor Inc
SP8852E/IG/HCAR
SP8852 - 2.7GHz Parallel Load Professional Synthesiser '
1000 units: 39.49 USD
500 units: 41.81 USD
100 units: 43.67 USD
25 units: 45.53 USD
1 units: 46.46 USD
Distributor
Rochester Electronics

376 In Stock
BuyNow BuyNow
Gps
SP8852D/IG/HCAR
PLL FREQUENCY SYNTHESIZER, CQCC44 (Also Known As: SP8852EIG)
71 units: 55 USD
34 units: 57.5 USD
1 units: 65 USD
Distributor
Quest Components

101 In Stock
BuyNow BuyNow





Similar Datasheet

Part Number Description
SP8852
manufacturer
Mitel Networks
27GHz Parallel Load Professional Synthesiser
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8852D
manufacturer
Zarlink Semiconductor
1.7GHz PARALLEL LOAD PROFESSIONAL SYNTHESISER
Obsolescence Notice This product is obsolete. This information is available for your convenience only. www.DataSheet4U.com For more information on Zarlink’s obsolete products and replacement product lists, please visit http://products.zarlink.com/obsolete_products/ SP8852D PACKAGE DETAILS Dimensions are shown thus: mm (in). For further package information please contact your local Customer Service Centre. 17.27/17.78 (0.680/0.700) 16.33/16.81 (0.643/0.662) 12.45/12.95 (0.490/0.510) 0.51 (0.02) NOM AT 45° INDEX CORNER 16.33/16.81 (0.643/0.662) 17.27/17.78 (0.680/0.700) 0.76MM(0.030 ″) 0.43MM(0.017 ″) 1.27/(0.050) NOM  1.02MM/(0.040I )NOM 45° AT 3 PLACES 0.89(0.035) 03.05/3.43 (0...
SP8852E
manufacturer
Mitel Networks
27GHz Parallel Load Professional Synthesiser
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8852EIGHCAR
manufacturer
Mitel Networks
27GHz Parallel Load Professional Synthesiser
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8852EKGHCAR
manufacturer
Mitel Networks
27GHz Parallel Load Professional Synthesiser
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8853
manufacturer
Mitel Networks
13GHz Professional Synthesiser
Prescaler and AM Counter The programmable divider chain is of AM counter design and therefore contains a dual modulus front end prescaler, an A counter which controls the dual modulus ratio and an M counter which controls the bulk multi-modulus division. A programmable divider of this type has a division ratio of MN1A and a minimum integer steppable division ratio of N(N21). In the SP8853, the dual modulus front end prescaler is a dual N ratio device, capable of being statically switched between 416/17 and 48/9 ratios. The controlling A counter is of four-bit design, allowing a maximum count sequence of 15 (2421), which begins with the start of the M counter sequence and stops when it has co...
SP8853
manufacturer
Zarlink Semiconductor
1.3 GHz Professional Synthesiser
Prescaler and AM Counter The programmable divider chain is of AM counter design and therefore contains a dual modulus front end prescaler, an A counter which controls the dual modulus ratio and an M counter which controls the bulk multi-modulus division. A programmable divider of this type has a division ratio of MN1A and a minimum integer steppable division ratio of N(N21). In the SP8853, the dual modulus front end prescaler is a dual N ratio device, capable of being statically switched between 416/17 and 48/9 ratios. The controlling A counter is of four-bit design, allowing a maximum count sequence of 15 (2421), which begins with the start of the M counter sequence and stops when it has co...
SP8853A
manufacturer
Mitel Networks
13GHz Professional Synthesiser
Prescaler and AM Counter The programmable divider chain is of AM counter design and therefore contains a dual modulus front end prescaler, an A counter which controls the dual modulus ratio and an M counter which controls the bulk multi-modulus division. A programmable divider of this type has a division ratio of MN1A and a minimum integer steppable division ratio of N(N21). In the SP8853, the dual modulus front end prescaler is a dual N ratio device, capable of being statically switched between 416/17 and 48/9 ratios. The controlling A counter is of four-bit design, allowing a maximum count sequence of 15 (2421), which begins with the start of the M counter sequence and stops when it has co...
SP8853AHC
manufacturer
Mitel Networks
13GHz Professional Synthesiser
Prescaler and AM Counter The programmable divider chain is of AM counter design and therefore contains a dual modulus front end prescaler, an A counter which controls the dual modulus ratio and an M counter which controls the bulk multi-modulus division. A programmable divider of this type has a division ratio of MN1A and a minimum integer steppable division ratio of N(N21). In the SP8853, the dual modulus front end prescaler is a dual N ratio device, capable of being statically switched between 416/17 and 48/9 ratios. The controlling A counter is of four-bit design, allowing a maximum count sequence of 15 (2421), which begins with the start of the M counter sequence and stops when it has co...




logo    Since 2024. D4U Semiconductor.   |   Contact Us   |   Privacy Policy