logo

SP8854E Mitel Networks 27GHz Parallel Load Professional Synthesiser Datasheet

SP8854E/KG/HCAR PLL FREQUENCY SYNTHESIZER, BIPOL


Mitel Networks
SP8854E
Part Number SP8854E
Manufacturer Mitel Networks
Description These pins are the data inputs to set the RF divider ratio (MN1A). High is open circuit on these pins. Data is transparent from pins to RF buffer when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC...
Features s 2
·7 GHz Operating Frequency s Single 5V Supply s Low Power Consumption <1
·3W s High Comparison Frequency : 20MHz s High Gain Phase Detector : 1mA/rad s Zero ‘Dead Band’ Phase Detector s Wide Range of RF and Reference Division Ratios s Programming by Single Word Data Transfer ABSOLUTE MAXIMUM RATINGS Supply voltage Operating temperature Storage temperature Prescaler and reference input voltage Data inputs Junction temperature 20
·3V to 16V 255°C to1100°C 265°C to 1150°C 2
·5V p-p VCC 10
·3V VEE 20
·3V 1175°C DATA BIT 4 DATA BIT 3 DATA BIT 2 DATA BIT 1 DATA BIT 0 0V (PRESCALER) RF INPUT RF INPUT ...

Document Datasheet SP8854E datasheet pdf (176.32KB)
Distributor Distributor
DigiKey
Stock 23 In Stock
Price
3 units: 122.78 USD
BuyNow BuyNow BuyNow (Manufacturer a Zarlink Semiconductor Inc)




SP8854E Distributor

Zarlink Semiconductor Inc
SP8854E/KG/HCAR
PLL FREQUENCY SYNTHESIZER, BIPOL
3 units: 122.78 USD
Distributor
DigiKey

23 In Stock
BuyNow BuyNow
Zarlink Semiconductor Inc
SP8854E/KG/HCAR
SP8854 - 2.7GHz Parallel Load Professional Synthesiser '
1000 units: 105.37 USD
500 units: 111.57 USD
100 units: 116.53 USD
25 units: 121.48 USD
1 units: 123.96 USD
Distributor
Rochester Electronics

23 In Stock
BuyNow BuyNow
Microsemi Corporation
SP8854E/IG/HCAR
PLL FREQUENCY SYNTHESIZER, BIPOLAR, CQCC44
204 units: 75 USD
98 units: 78.75 USD
1 units: 97.5 USD
Distributor
Quest Components

288 In Stock
BuyNow BuyNow





Similar Datasheet

Part Number Description
SP8852
manufacturer
Mitel Networks
27GHz Parallel Load Professional Synthesiser
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8852D
manufacturer
Zarlink Semiconductor
1.7GHz PARALLEL LOAD PROFESSIONAL SYNTHESISER
Obsolescence Notice This product is obsolete. This information is available for your convenience only. www.DataSheet4U.com For more information on Zarlink’s obsolete products and replacement product lists, please visit http://products.zarlink.com/obsolete_products/ SP8852D PACKAGE DETAILS Dimensions are shown thus: mm (in). For further package information please contact your local Customer Service Centre. 17.27/17.78 (0.680/0.700) 16.33/16.81 (0.643/0.662) 12.45/12.95 (0.490/0.510) 0.51 (0.02) NOM AT 45° INDEX CORNER 16.33/16.81 (0.643/0.662) 17.27/17.78 (0.680/0.700) 0.76MM(0.030 ″) 0.43MM(0.017 ″) 1.27/(0.050) NOM  1.02MM/(0.040I )NOM 45° AT 3 PLACES 0.89(0.035) 03.05/3.43 (0...
SP8852E
manufacturer
Mitel Networks
27GHz Parallel Load Professional Synthesiser
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8852E
manufacturer
Zarlink Semiconductor
1.7GHz PARALLEL LOAD PROFESSIONAL SYNTHESISER
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8852EIGHCAR
manufacturer
Mitel Networks
27GHz Parallel Load Professional Synthesiser
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8852EKGHCAR
manufacturer
Mitel Networks
27GHz Parallel Load Professional Synthesiser
These are the inputs to the 16-bit data bus. When pin 38 is high the data goes to the buffers for the A counter, M counter and phase detector gain. When pin 38 is low the data goes to the buffers for the reference counter and the phase detector state (see Table 4). Open circuit = 1 (high) on these pins. Data is transparent from pins to the selected buffers when pin 39 (STROBE) is high and frozen in buffers when pin 39 is low. Balanced inputs to the RF preamplifier. For single-ended operation the signal is AC-coupled into pin 13 with pin 14 AC-decoupled to ground (or vice-versa). Pins 13 and 14 are internally DC biased. A current sink into this pin is enabled when the lock detect circuit indi...
SP8853
manufacturer
Mitel Networks
13GHz Professional Synthesiser
Prescaler and AM Counter The programmable divider chain is of AM counter design and therefore contains a dual modulus front end prescaler, an A counter which controls the dual modulus ratio and an M counter which controls the bulk multi-modulus division. A programmable divider of this type has a division ratio of MN1A and a minimum integer steppable division ratio of N(N21). In the SP8853, the dual modulus front end prescaler is a dual N ratio device, capable of being statically switched between 416/17 and 48/9 ratios. The controlling A counter is of four-bit design, allowing a maximum count sequence of 15 (2421), which begins with the start of the M counter sequence and stops when it has co...
SP8853
manufacturer
Zarlink Semiconductor
1.3 GHz Professional Synthesiser
Prescaler and AM Counter The programmable divider chain is of AM counter design and therefore contains a dual modulus front end prescaler, an A counter which controls the dual modulus ratio and an M counter which controls the bulk multi-modulus division. A programmable divider of this type has a division ratio of MN1A and a minimum integer steppable division ratio of N(N21). In the SP8853, the dual modulus front end prescaler is a dual N ratio device, capable of being statically switched between 416/17 and 48/9 ratios. The controlling A counter is of four-bit design, allowing a maximum count sequence of 15 (2421), which begins with the start of the M counter sequence and stops when it has co...
SP8853A
manufacturer
Mitel Networks
13GHz Professional Synthesiser
Prescaler and AM Counter The programmable divider chain is of AM counter design and therefore contains a dual modulus front end prescaler, an A counter which controls the dual modulus ratio and an M counter which controls the bulk multi-modulus division. A programmable divider of this type has a division ratio of MN1A and a minimum integer steppable division ratio of N(N21). In the SP8853, the dual modulus front end prescaler is a dual N ratio device, capable of being statically switched between 416/17 and 48/9 ratios. The controlling A counter is of four-bit design, allowing a maximum count sequence of 15 (2421), which begins with the start of the M counter sequence and stops when it has co...
SP8853AHC
manufacturer
Mitel Networks
13GHz Professional Synthesiser
Prescaler and AM Counter The programmable divider chain is of AM counter design and therefore contains a dual modulus front end prescaler, an A counter which controls the dual modulus ratio and an M counter which controls the bulk multi-modulus division. A programmable divider of this type has a division ratio of MN1A and a minimum integer steppable division ratio of N(N21). In the SP8853, the dual modulus front end prescaler is a dual N ratio device, capable of being statically switched between 416/17 and 48/9 ratios. The controlling A counter is of four-bit design, allowing a maximum count sequence of 15 (2421), which begins with the start of the M counter sequence and stops when it has co...




logo    Since 2024. D4U Semiconductor.   |   Contact Us   |   Privacy Policy